Yes, in most cases. Removing the curb changes the finished floor elevation at the valve rough-in, and that shift often pushes the control location outside the 38 to 48 inch zone required by ADA 608.4. If the valve was never rated ASSE 1016 to begin with, the conversion is the moment that gets flagged, because barrier-free showers fall under the accessible shower provisions regardless of whether the original stall was built to that standard.
Why Curbless Floors Change Control Height
A standard curb shower has a flat pan with the valve set at a height measured from a fixed floor plane. Curbless construction replaces that flat plane with a sloped one, typically running to a linear or point drain at 1:48 (2 percent) maximum slope per ADA and ANSI A117.1. That slope is measured across the entire shower floor, which means the elevation at the valve wall is not the same as the elevation at the drain wall.
If the rough-in height was set using the old curb-shower finished floor elevation, and the contractor then builds a sloped mud bed or preformed pan to meet the drain, the valve can end up anywhere from half an inch to over an inch off from the original plan, depending on the distance from the valve to the high point of the slope. On a 60 inch wide stall sloped at 2 percent, that is more than an inch of difference between the two walls. Inspectors measure from the finished floor directly below the control, not from a framing reference, so this error shows up at final inspection, not during rough-in.
ASSE 1016 Valves in Barrier-Free Showers
ASSE 1016 covers pressure-balancing and thermostatic mixing valves, and it is the standard most plumbing codes reference for shower valves generally, not just accessible ones. But in a barrier-free or curbless shower, the stakes for scald protection are higher because the design intent is often aging-in-place or wheelchair transfer, where a user may have slower reaction time or reduced mobility to escape a temperature spike.
A pressure-balance valve maintains a fixed ratio of hot to cold when supply pressure fluctuates, for example when a toilet flushes elsewhere in the building. A thermostatic valve goes further and maintains a set output temperature regardless of supply temperature changes, which matters more in commercial and multifamily buildings with variable water heater recovery. Either valve type satisfies ASSE 1016 if properly listed, but thermostatic valves are increasingly specified for curbless conversions in institutional and healthcare-adjacent projects because they allow a fixed temperature limit stop in addition to the pressure-balance function.
If the existing valve is a basic two-handle or single-handle non-compensating valve, it does not meet ASSE 1016 and must be replaced regardless of the floor work. This is worth flagging early, because swapping the valve body often means opening the wall, which changes the scope and schedule of what the GC may have priced as a floor-only conversion.
ADA 608.4 Control Zone vs Trench Drains
ADA 608.4 requires shower controls, faucets, and shower heads to be operable with one hand and not require tight grasping, pinching, or twisting of the wrist, and it sets the control location between 38 and 48 inches above the shower floor. The phrase “above the shower floor” is where curbless conversions create a measurement problem, because a sloped floor does not have one elevation, it has a range.
Trench drains complicate this further. A linear drain at the entry wall, opposite the valve wall, means the floor at the valve location is at its highest point, which is correct for drainage but also means the control is effectively closer to the ceiling than it would be with the drain centered. If the valve wall is also the entry wall, as it sometimes is to simplify plumbing runs, the floor there is at its lowest point, and the measured control height increases relative to that lower plane, which can push it above 48 inches if the rough-in was not adjusted for slope.
The fix is to set the valve rough-in using the finished floor elevation directly below the control location, not the plan elevation at the drain or the curb line. On projects where the valve wall and drain wall are not the same plane, this number is not something you can get from a generic framing chart. It has to be calculated from the actual slope and drain placement for that stall.
Offset Controls and Reach Range Conflicts
ADA 308 governs reach range and splits into forward reach and side reach, each with different maximum and minimum heights depending on obstructions. A control mounted on the wall directly in front of a wheelchair user, with no obstruction, falls under unobstructed forward reach, capped at 48 inches high and no lower than 15 inches. A control mounted on a side wall, which is far more common in curbless showers with a fixed shower seat, falls under side reach provisions.
The conflict shows up when a designer offsets the valve to the opposite end of the stall from the seat, often to keep plumbing away from the seat wall for structural reasons. That offset can turn what should be a side reach into a forward reach if the seat is fixed and the user cannot approach the control wall directly, or it can exceed the maximum reach distance if there is any obstruction like a grab bar or partial wall between the user’s seated position and the control.
For transfer-type shower compartments, ADA 608.3 also specifies the control location relative to the seat wall, generally within 27 inches of the centerline, which supersedes a purely height-based read of 608.4. If the architect’s seat placement was finalized after the valve rough-in, double check that the resulting reach distance is still within an unobstructed 10 to 24 inch range for forward reach, or the equivalent side reach distances, rather than relying on height alone.
Inspection Checklist for Converted Stalls
Before calling for final inspection on a curbless conversion, verify the following against the as-built conditions, not the original drawings:
- Valve is listed ASSE 1016, pressure-balance or thermostatic, and the listing label is visible or documented in submittals.
- Control height is measured from the finished floor directly below the control, accounting for slope, and falls between 38 and 48 inches.
- Slope across the shower floor does not exceed 1:48 (2 percent) at any point, verified with a level and story pole, not assumed from the drain detail.
- Reach to the control from the seat position, if a fixed seat exists, meets forward or side reach requirements under ADA 308, with obstructions accounted for.
- Shower head and hand shower, where provided, meet the same control-height logic if they share a single-hand operable requirement.
Where the project is replacing trim only and reusing an existing rough valve body, confirm the valve body itself is already ASSE 1016 rated before ordering shower faucet sets for the finish work, since trim kits do not change the pressure-balance or thermostatic function of the valve behind the wall. Mixing a new trim plate on a non-compliant rough valve will pass a visual walkthrough but fail if the inspector pulls the cut sheet or asks for the valve model number.
| Item | Standard | Typical failure point in curbless conversion |
|---|---|---|
| Valve type | ASSE 1016 | Reusing old two-handle valve without pressure balance or thermostatic function |
| Control height | ADA 608.4, 38 to 48 in. | Height measured from plan elevation instead of actual sloped floor |
| Floor slope | Max 1:48 (2%) | Slope exceeds 2% to reach drain, pushing valve height out of range |
| Reach range | ADA 308 | Offset valve location creates obstructed reach from fixed seat |
If you are bidding or inspecting a curbless conversion, get the slope and drain shop drawings before finalizing the valve rough-in height, not after. On any project where the seat location, drain type, or valve wall changes from the original design, recalculate the control height and reach distance rather than reusing the dimension from the prior curb-shower layout. When the numbers are close to a limit, bring in the architect or accessibility consultant of record before the wall is closed, since reopening finished tile to move a valve costs far more than adjusting a rough-in sketch.
